Engine Mount Bolts

KE 336 · Post by **KE 336** » December 30th, 2008, 6:18 am

Forgive me if it has been covered before, but I haven't seen it anywhere.
Obviously with the thicker mounting brackets the stock bolts won't be long enough. What's everbody using?

robertg · Post by **robertg** » December 30th, 2008, 6:42 am

95701-10160-08 is 160mm long.

Post by **AlisoBob** » December 30th, 2008, 7:29 am

robertg wrote:95701-10160-08 is 160mm long.

Hows that for an answer???

teemtrubble · Post by **teemtrubble** » December 30th, 2008, 8:36 am

Measure the overall dimension of your motor mounts and let me know and I'll get you the part numbers.

agent · Post by **agent** » December 30th, 2008, 1:45 pm

Yea, Mike... when you look those up, add them to the list

Rick

teemtrubble · Post by **teemtrubble** » December 30th, 2008, 1:56 pm

My conversions come with them

KE 336 · Post by **KE 336** » December 31st, 2008, 3:07 pm

Thanks guys!
Mike, I haven't gotten that far yet. I'm using 3/4" X 2 1/2" flat to make the mounts but might mill a small recess on them for the bolt head and nut
but not sure just yet.

jarnott71 · Post by **jarnott71** » September 15th, 2010, 9:49 am

i looked at a couple oem parts sites but that number dosent match anything. what steelership do you guys get the bolt from, or what honda bike used the 10x160 bolt. im prob looking in the wrong places as i always seem to do. if somebody could slap me in the right direction id be ok. thanks

KE 336 · Post by **KE 336** » September 15th, 2010, 3:41 pm

It will take some looking on your part but, go to honda dealer of choice that has parts finder and look at different bikes and years. Look under the "frame" section. If you look at the item # on the parts list it says the size of the bolt. One bolt on the 02-04 crf450 is 10x170 mm which is the one I ended up using.

Mik329 · Post by **Mik329** » September 15th, 2010, 6:59 pm

90101-HP1-000 is 10x162. its from a 2005 TRX450R. I have one here and it worked great with Pauls mounts

pstoffers · Post by **pstoffers** » September 15th, 2010, 11:37 pm

Mik329 wrote:90101-HP1-000 is 10x162. its from a 2005 TRX450R. I have one here and it worked great with Pauls mounts

I use the 95701-10160-08 its 10X160 and a few bucks cheeper than that one Mik

blackz34 · Post by **blackz34** » September 17th, 2010, 4:25 pm

When i'm looking for an OEM bolt of a specific lenght, I just go on a website selling OEM parts (like babbitsonline) and I enter the make (honda) and 10x162 (or any other size!) and it gives me all the application for this bolt. Sometimes you have to try a couple of time to find the closest lenght you need.

OUTKAST INC. · Post by **OUTKAST INC.** » September 17th, 2010, 4:47 pm

i went ti bolts from race bolts , very cool cause the have 12mm hex on bolt and nuts

BannedCR500Riders.com

Engine Mount Bolts

Engine Mount Bolts