Milling Machine
- maddog1927
- Posts: 313
- Joined: April 4th, 2010, 8:10 am
- Location: Mesa, AZ
Milling Machine
Bridgeport Series 1 Variable Drive
Sony DRO
Full set of R8 collets plus holder
X axis power feed
Single shot lube system
6" Vise
8" Rotary table
Misc Tooling
Phase converter (Static)
$2500 Delivered Phoenix metro
Possible deliver to the Lakeside AZ area, maybe to LA area, depending on what trips I have coming up.
A nice addition to any shop.
Sony DRO
Full set of R8 collets plus holder
X axis power feed
Single shot lube system
6" Vise
8" Rotary table
Misc Tooling
Phase converter (Static)
$2500 Delivered Phoenix metro
Possible deliver to the Lakeside AZ area, maybe to LA area, depending on what trips I have coming up.
A nice addition to any shop.
- Roostius_Maximus
- Site Admin
- Posts: 4641
- Joined: November 16th, 2007, 3:24 pm
- Location: Mt Nebo, Manitoba, Canada
- Contact:
http://www.youtube.com/user/500bigbore
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
- maddog1927
- Posts: 313
- Joined: April 4th, 2010, 8:10 am
- Location: Mesa, AZ
- Roostius_Maximus
- Site Admin
- Posts: 4641
- Joined: November 16th, 2007, 3:24 pm
- Location: Mt Nebo, Manitoba, Canada
- Contact:
sweet
http://www.youtube.com/user/500bigbore
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
- Roostius_Maximus
- Site Admin
- Posts: 4641
- Joined: November 16th, 2007, 3:24 pm
- Location: Mt Nebo, Manitoba, Canada
- Contact:
thats pretty reasonable $ if that dro, vice, clamp set and rotary table come with
http://www.youtube.com/user/500bigbore
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
-
- Posts: 4394
- Joined: July 4th, 2007, 6:57 pm
- maddog1927
- Posts: 313
- Joined: April 4th, 2010, 8:10 am
- Location: Mesa, AZ
PM sent.roost251 wrote:Maddog, could you recomend any repair shops in AZ, I have a bridge port like yours(the one you are selling) and it needs new spindles bearings and a general going through. Thanks!
You could also call tom moore of moore tool and equipment. he seems to give good recomendations. He told me who to call to move the mill, and it worked out well
- Roostius_Maximus
- Site Admin
- Posts: 4641
- Joined: November 16th, 2007, 3:24 pm
- Location: Mt Nebo, Manitoba, Canada
- Contact:
hey, I'm looking for something like this....
http://www.wttool.com/index/page/catego ... teChampion
my others are .200" shaft tip with a flat end, i'd prefer one the same, no ball end.
Any ideas on where to look?
http://www.wttool.com/index/page/catego ... teChampion
my others are .200" shaft tip with a flat end, i'd prefer one the same, no ball end.
Any ideas on where to look?
http://www.youtube.com/user/500bigbore
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd