Building Tips, Suspension Set Ups, Conversion Parts .... Build to your Heart's Content!
Mik329
Posts: 493 Joined: October 2nd, 2007, 2:23 pm
Location: Cumming, GA
Post
by Mik329 » January 20th, 2009, 1:04 pm
Tired of pulling the motor in and out while doing a mock up? These are good for bolting everything together during welding for no movement. I accept paypal for payment. $60 flat rate shipping lower 48. $70 for Europe/ Australia
Last edited by
Mik329 on February 1st, 2010, 11:22 am, edited 2 times in total.
aloha450x
Posts: 874 Joined: December 8th, 2007, 12:38 am
Post
by aloha450x » January 20th, 2009, 8:47 pm
that's awesome. way to step up.
CRMOE500
Posts: 305 Joined: April 7th, 2008, 3:30 pm
Location: Fin Land,Canada
Post
by CRMOE500 » January 30th, 2009, 8:40 pm
Nice work Mik329. How about an extra piece on top for the headstay?
Fins Rule!
Liquids drool.
"If the rule you followed led you to this of what use was the rule?" Anton Chigurh
NightBiker07
Posts: 1942 Joined: April 16th, 2008, 8:59 pm
Location: USA
Post
by NightBiker07 » January 31st, 2009, 6:30 pm
Wicked Sick!
2000 CR250, pipe, filter, Vforce
1980 XL80s
1969 Broncco TX-6
Natural selection favors Smart people, so nature selects morons to be slow and dumb for tigers and stuff too eat. But in our modern world there just aren't enough tigers.
Mik329
Posts: 493 Joined: October 2nd, 2007, 2:23 pm
Location: Cumming, GA
Post
by Mik329 » February 1st, 2009, 1:06 pm
KE336, your jig is going out in the morning. Thanks
Mik329
Posts: 493 Joined: October 2nd, 2007, 2:23 pm
Location: Cumming, GA
Post
by Mik329 » February 3rd, 2009, 4:33 am
CRMOE500 wrote: Nice work Mik329. How about an extra piece on top for the headstay?
I can do this for you if you need, I just didn't think it was needed with Shanman's headstay available.
KE 336
Posts: 223 Joined: May 9th, 2008, 8:14 pm
Location: FT. Worth,TX
Post
by KE 336 » February 5th, 2009, 7:18 am
Got my jig in the mail yesterday! Going to be alot easier moving that in and out of the frame than a motor. Should also give alot more hand room for taking measurements for mount fabrication.
Thanks Mik!
AngryShawn
Posts: 173 Joined: September 3rd, 2007, 9:33 pm
Contact:
Post
by AngryShawn » February 5th, 2009, 10:58 am
Looks sweet, way to support the community!
4Z
Posts: 299 Joined: February 7th, 2008, 7:38 pm
Location: Western WA
Contact:
Post
by 4Z » February 22nd, 2009, 8:03 am
Good eye Johnny!
Mik329
Posts: 493 Joined: October 2nd, 2007, 2:23 pm
Location: Cumming, GA
Post
by Mik329 » March 11th, 2009, 1:37 pm
Note: I have these listed on Ebay for more than I offer to board members here. These are discounted to this board only as a way of helping fellow hoons out and for the fact that I favor this board over others.
Thanks
AlisoBob
"Hoon-father"
Posts: 15404 Joined: May 31st, 2007, 6:39 pm
Location: Aliso Viejo Ca
Post
by AlisoBob » March 11th, 2009, 1:38 pm
bulitnv
Posts: 25 Joined: February 20th, 2009, 6:44 pm
Location: Whittier CA
Post
by bulitnv » March 11th, 2009, 2:00 pm
saw these on EBAY, great idea!
2007 CRF450R
2002 CR500AF Service Honda
1971 Yamaha CT-1
1971 Honda CT-70
perrymx52
Posts: 3 Joined: February 22nd, 2009, 1:35 pm
Post
by perrymx52 » March 12th, 2009, 4:35 pm
Ordered mine today. Pickup my 500 hunnie tomorrow. Already had it bought, just had to wait for the lucky b@#*@rd to get back from Daytona.
Might need some help with posting the photos of the build. I do okay with taking the pictures and posting on ebay and craigslist. Not sure if that's how it's done here.
Doing the conversion into an 08 crf250 chassis. Might be looking for a triple clamp as it has a 22mm Ride Eng. on it now. Think it might make it a little busy up front.
Thanks again Mik329 for the great product.
Mik329
Posts: 493 Joined: October 2nd, 2007, 2:23 pm
Location: Cumming, GA
Post
by Mik329 » March 12th, 2009, 5:28 pm
It will be at the post office at 9am tomorrow.
Thanks!
iggys-amsoil
Posts: 3602 Joined: June 1st, 2007, 6:09 pm
Location: Just North of March Airfield CA
Post
by iggys-amsoil » March 12th, 2009, 6:17 pm
perrymx52 wrote:
Doing the conversion into an 08 crf250 chassis. Might be looking for a triple clamp as it has a 22mm Ride Eng. on it now.
I have the stock 03 CR250 one that I could part with but I don't know if it would work on the CRF. Thinking not.
Luke
Posts: 19 Joined: March 10th, 2009, 8:01 am
Post
by Luke » May 7th, 2009, 8:14 am
hey mike you got any of these Jigs left, ? I need of one, makes life alot easier!!
Mik329
Posts: 493 Joined: October 2nd, 2007, 2:23 pm
Location: Cumming, GA
Post
by Mik329 » May 7th, 2009, 1:11 pm
I have enough metal for a couple more and can weld one up for you in the next few days or so.
Luke
Posts: 19 Joined: March 10th, 2009, 8:01 am
Post
by Luke » May 7th, 2009, 3:39 pm
sounds good mike, how much do you charge, and where you at,
Mik329
Posts: 493 Joined: October 2nd, 2007, 2:23 pm
Location: Cumming, GA
Post
by Mik329 » May 8th, 2009, 4:26 am
Luke wrote: sounds good mike, how much do you charge, and where you at,
check your PM
seanmx57
Posts: 728 Joined: January 1st, 2009, 2:28 pm
Post
by seanmx57 » June 10th, 2009, 3:31 pm
I'd like to build my own, I have a stick welder and a MIG. What tubing are you using? I'm a novice welder, any tips?
I have a SH 2000 frame to use as a jig.
Mik329
Posts: 493 Joined: October 2nd, 2007, 2:23 pm
Location: Cumming, GA
Post
by Mik329 » June 11th, 2009, 5:01 am
I'm using 1/2" tubing for the triangle, the swingarm/engine collar are ordered for the proper ID to fit the swingarm and engine bolts. I'm not at home, so I do not have the size handy.
Mik329
Posts: 493 Joined: October 2nd, 2007, 2:23 pm
Location: Cumming, GA
Post
by Mik329 » June 15th, 2009, 7:40 am
John and Ben, check your PM's for tracking numbers- jigs went out this morning.
Thanks!
Mik329
Posts: 493 Joined: October 2nd, 2007, 2:23 pm
Location: Cumming, GA
Post
by Mik329 » June 28th, 2009, 5:50 pm
I have metal for about a dozen jigs now and will be putting some together in the next few days.
homenf
Posts: 219 Joined: October 11th, 2009, 10:35 am
Location: Sparks, NV
Post
by homenf » November 16th, 2009, 11:24 am
I'm working on getting a crf250 roller. If I do could I buy a jig from you?
homenf
Posts: 219 Joined: October 11th, 2009, 10:35 am
Location: Sparks, NV
Post
by homenf » November 16th, 2009, 10:20 pm
bought it today, so let me know.
Thanks