wtb 2000 or 2001 swingarm and linkage cr250

Come on in, No registration needed.... Thinkin' about stepping up to the ultimate dirtbike? Ask any questions you need answered.

ALSO: Post anything your looking for, or that is taking up space and you want to get ride of.. ALL TRANSACTIONS ARE BETWEEN THE BUYER / SELLER!
Post Reply
lms1977
Posts: 42
Joined: March 23rd, 2013, 2:45 pm

wtb 2000 or 2001 swingarm and linkage cr250

Post by lms1977 »

I need a 2000 or 2001 swingarm and linkage for a cr250 thank mike 484-554-5829

It does not need to be perfect or have good bearings
Top
User avatar
Roostius_Maximus
Site Admin
Posts: 4641
Joined: November 16th, 2007, 3:24 pm
Location: Mt Nebo, Manitoba, Canada
Contact:
Contact Roostius_Maximus

Post by Roostius_Maximus »

Up o 04 fits too
Top
lms1977
Posts: 42
Joined: March 23rd, 2013, 2:45 pm

Post by lms1977 »

Roostius_Maximus wrote:Up o 04 fits too
Are you sure on this? If so that should make it easier to find one
Top
User avatar
Roostius_Maximus
Site Admin
Posts: 4641
Joined: November 16th, 2007, 3:24 pm
Location: Mt Nebo, Manitoba, Canada
Contact:
Contact Roostius_Maximus

Post by Roostius_Maximus »

You could use up to a 2012, just different chain slider
Top
lms1977
Posts: 42
Joined: March 23rd, 2013, 2:45 pm

Post by lms1977 »

Well when I got the bike in pcs the kid took the swinger and put it on his 2007 cr125 cause it has a broke chain tensioner bolt so I have the 2007 cr125 one and it is slightly too wide to fit I did work it over a little and got it to fit but had to remove one of the spacer washers that the thin needle bearing rides on.. not the needle bearing will ride on the bushing that goes thru the seal which will only contact the bearing 2/3 of the way :( and im sure it wont last... I can machine the bore deeper but that will be a pain
Top
User avatar
jar944
Posts: 57
Joined: August 12th, 2009, 7:15 am

Post by jar944 »

lms1977 wrote:Well when I got the bike in pcs the kid took the swinger and put it on his 2007 cr125 cause it has a broke chain tensioner bolt so I have the 2007 cr125 one and it is slightly too wide to fit I did work it over a little and got it to fit but had to remove one of the spacer washers that the thin needle bearing rides on.. not the needle bearing will ride on the bushing that goes thru the seal which will only contact the bearing 2/3 of the way :( and im sure it wont last... I can machine the bore deeper but that will be a pain
Just build a line boring jig. Shouldn't take much time at all. I'd lend you the one I use on KTM swingarms if it would fit.
Top
lms1977
Posts: 42
Joined: March 23rd, 2013, 2:45 pm

Post by lms1977 »

jar944 wrote:
lms1977 wrote:Well when I got the bike in pcs the kid took the swinger and put it on his 2007 cr125 cause it has a broke chain tensioner bolt so I have the 2007 cr125 one and it is slightly too wide to fit I did work it over a little and got it to fit but had to remove one of the spacer washers that the thin needle bearing rides on.. not the needle bearing will ride on the bushing that goes thru the seal which will only contact the bearing 2/3 of the way :( and im sure it wont last... I can machine the bore deeper but that will be a pain
Just build a line boring jig. Shouldn't take much time at all. I'd lend you the one I use on KTM swingarms if it would fit.
THanks Jared but I think I figured out a easier fix I can just surface grind the spacers and washers down to make it work I think.. but now the linkage is too wide to fit the swinger :( im gonna take a measurement and mill the swinger to fit the linkage. If it works I'll debate about the line boring idea or just modding the spacers..
Top
Post Reply

Return to “Shoppers Only!”