1" Square 6061 T-6 Tubing Available
1" Square 6061 T-6 Tubing Available
This matches the original tubing very well, incorporates the OEM .125" radius on the exterior.
This is the stuff you need for your A/F conversions!
Aerospace quality...Sold by the foot, $7.50 per
PM me with orders.... paypal accepted.
This is the stuff you need for your A/F conversions!
Aerospace quality...Sold by the foot, $7.50 per
PM me with orders.... paypal accepted.
- teemtrubble
- Posts: 2269
- Joined: October 11th, 2007, 2:15 pm
- Location: simi valley, ca
Can 1" square stock be used??? Have access to about 6' of it. My conversion is going to be an 08 crf250. Was wondering if it could be used instead of the square tubing??? Friend of my will give me the square stock. From Bob's build it looks like he only used about 5-7 inches per side?? Thanks in advance.
- Roostius_Maximus
- Site Admin
- Posts: 4641
- Joined: November 16th, 2007, 3:24 pm
- Location: Mt Nebo, Manitoba, Canada
- Contact:
Thanks for the kick!
i'll take paypal, email me or PM, likely i can ship it the same day
my username @live.com
i'll take paypal, email me or PM, likely i can ship it the same day
my username @live.com
http://www.youtube.com/user/500bigbore
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
-
- Posts: 4394
- Joined: July 4th, 2007, 6:57 pm
-
- Posts: 4394
- Joined: July 4th, 2007, 6:57 pm
- Roostius_Maximus
- Site Admin
- Posts: 4641
- Joined: November 16th, 2007, 3:24 pm
- Location: Mt Nebo, Manitoba, Canada
- Contact:
my stuff used to have the grade and everything printed on it, then to cheappen it they dropped the print, now its only on the pallet of the tube instead of each individual piece
http://www.youtube.com/user/500bigbore
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
-
- Posts: 4394
- Joined: July 4th, 2007, 6:57 pm
-
- Posts: 4394
- Joined: July 4th, 2007, 6:57 pm
i got a bunch of gen3 tube on its way 1"x1" x .125 (1/8 thick) x .125 ( 1/8 outside radius) x .062 (1/16 inside radius). the whole lot will be annealed to 0. assuming the fab shop doesnt fuck up any bends then i should have a bunch left over. it wont work for you however unless your doing a heat treat method. its still about 3 weeks out untill i have the finished product in my hands but ill keep you guys posted in case i have some extra incase a hoon needs some.
-
- Posts: 31
- Joined: May 17th, 2009, 8:09 am
- Location: Savannah,Georgia
-
- Posts: 4394
- Joined: July 4th, 2007, 6:57 pm
-
- Posts: 4394
- Joined: July 4th, 2007, 6:57 pm
- Roostius_Maximus
- Site Admin
- Posts: 4641
- Joined: November 16th, 2007, 3:24 pm
- Location: Mt Nebo, Manitoba, Canada
- Contact:
right here, and i send ALOT south too
http://www.youtube.com/user/500bigbore
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
My CR500 Tech Reference... http://sdrv.ms/1a0CIiz
MRE Components... http://sdrv.ms/1bs2zhd
-
- Posts: 4394
- Joined: July 4th, 2007, 6:57 pm
i know where to get it $75 to your door in the western states. 20' made in the usa with certs. use what you need and sell the rest to other hoons at $7.50/ft and put a few bucks in your pocket like bob did . ill sell some of mine eventually, but i want to keep some extra until i get the bends correct incase i fuckup first time around.