my hillclimb vid
-
- Posts: 4394
- Joined: July 4th, 2007, 6:57 pm
my hillclimb vid
to a professional they probly aint real hills but i thought they were fun none the less
1 http://www.vimeo.com/1499198
2 http://www.vimeo.com/1499076
1 http://www.vimeo.com/1499198
2 http://www.vimeo.com/1499076
- britincali
- Posts: 8207
- Joined: May 31st, 2007, 7:10 pm
- Location: Barstow, CA
-
- Posts: 4394
- Joined: July 4th, 2007, 6:57 pm
britincali wrote:Your bike sounds rich as hell
X10
NAHA PRO HILLCLIMBER #216
LIVIN THE DREAM!!!
NOTHING BUT GREEN LABEL BLENDZALL!!!
http://sponsorhouse.loopd.com/Members/P ... /Home.aspx
http://www.pro-hillclimbers.org/
LIVIN THE DREAM!!!
NOTHING BUT GREEN LABEL BLENDZALL!!!
http://sponsorhouse.loopd.com/Members/P ... /Home.aspx
http://www.pro-hillclimbers.org/
-
- Posts: 1898
- Joined: June 23rd, 2007, 12:47 pm
- Location: Prescott
it looks like you mite want to shorten that swingarm alittle just so it will pull the front tire up if you pull on the bars alittle
you may want to play with it , the shorter the arm the more traction you will get
you may want to play with it , the shorter the arm the more traction you will get
"the game of life of is not so much in holding a good hand as playing a poor hand well"
-
- Posts: 4394
- Joined: July 4th, 2007, 6:57 pm
-
- Posts: 4394
- Joined: July 4th, 2007, 6:57 pm
-
- Posts: 4394
- Joined: July 4th, 2007, 6:57 pm
- iggys-amsoil
- Posts: 3602
- Joined: June 1st, 2007, 6:09 pm
- Location: Just North of March Airfield CA
-
- Posts: 193
- Joined: April 21st, 2008, 9:44 pm
- britincali
- Posts: 8207
- Joined: May 31st, 2007, 7:10 pm
- Location: Barstow, CA
- iggys-amsoil
- Posts: 3602
- Joined: June 1st, 2007, 6:09 pm
- Location: Just North of March Airfield CA
Chain break 101;
Open vise so pins fit the gap.
Use a box or whatever to support the rest of chain.
2 lb hammer using the flat side, back end of punch to get the pin flat.
Then punch or air hammer/rivet gun with punch MADE to fit said gun.
Enjoy.
Open vise so pins fit the gap.
Use a box or whatever to support the rest of chain.
2 lb hammer using the flat side, back end of punch to get the pin flat.
Then punch or air hammer/rivet gun with punch MADE to fit said gun.
Enjoy.
Trinity Racing mild porting FMF
62 pilot, EGH needle, 172 main
03 Gen III CR250 frame
2013 Dodger Charger 5.7 Hemi
http://www.prisonplanet.com
Your Amsoil Customer # 350882
62 pilot, EGH needle, 172 main
03 Gen III CR250 frame
2013 Dodger Charger 5.7 Hemi
http://www.prisonplanet.com
Your Amsoil Customer # 350882
-
- Posts: 4394
- Joined: July 4th, 2007, 6:57 pm
-
- Posts: 193
- Joined: April 21st, 2008, 9:44 pm